Wednesday, April 5, 2023

April's Free Embroidery


 


Wow, it's April already so here is this month's freebie! Follow this photo for flower placement or put them where you want.

I'm giving you some directions for the embroideries. You will need to know basic stitches and there are a LOT of youtube videos that can teach you any you don't.

1. Cut a square of your background fabric 5" x 5". This will be cut smaller later but this fits my fav 4" hoop. You can cut the fabric so it will fit in the embroidery hoop you like but make sure the birdhouse has enough room for the embroidery.

2. This step in optional but I like the stability. Now I add a square of Pelon Shape Flex interfacing. This is my favorite to use for all my embroidery designs because it's not stiff and it's easy to embroider thru. I cut the square of it slightly smaller the the entire piece. You can just add it to the center square if you prefer.

Most important!!  If you went ahead and traced the birdhouse do not use steam this can smear your tracing. I've used Pigma pens and had them smear slightly.

Note: I never use steam to apply the interfacing and it sticks fine.


3. Using a permanent marker like a Pigma pen or a Pilot Frixon pen, trace the design. You can just trace the house and roof.  Note that the Frixon pen will disappear when heat is applied. This is great if you made a mistake, just iron the fabric and start again.

4. The house can be appliqued like I did or just stitched with your favorite embroidery stitch.

-Trace the house on Heat n Bond by Therm-o-web. This is a product that makes appliqueing small pieces so much easier. TIP: Hold the iron on for just a few seconds or you will also melt the other side.

-Once it cools peel off the paper.

-Lay the fabric over the tracings and iron in place.

-Do a small blanket stitch with 1 strand of floss ( I used DMC white) around the entire house


5. Applique or stitch the roof like you did the house .

6. For the base use 2 strands of floss (I used DMC 310) to couch down 6 strands. Then I used 2 strands to back stitch along the top and bottom. 


7. The opening is filled in with straight stitches using 3 strands of floss.

-Then use 2 strands to go around the circle with stem stitch.

-Use 3 strands to make a 3 wrap french knot. (I used DMC 310 for all 3 stitches)


8. The flowers are stitched with 3 strands of floss (I used DMC 552) to make lazy daisy stitches. Make as many or as few as you want. 

- The centers can be beads or 2 wrap french knots with 2 strands of floss (I used DMC 745).


9. Fill in around the flowers with lazy daisy stitches for leaves using 6 strands of floss (I used DMC 989).


10. Fill in around the flowers and leaves with 2-3 wrap french knots using 3 strands of floss (I used DMC 554).


 Right click the pattern to save it to your hard drive. You'll need to print a pattern for tracing.



 

©Billie Jo Heisler 2023

All rights reserved


 Disclaimer:

I drew this design by hand then used a software program to edit it.

Please consider the drawing copyrighted. You have my permission to print copies of the drawing in any size for your own use but not to share or sell. If you want to share the pattern please link to the blog pages.

The embroidery design is my own. I have not knowingly copied anyone else's work.


No comments:

Post a Comment

I look forward to reading messages from those who have kind words to share. I tend to only get on blogger once a week so if you leave a post that requires an answer please be patient with me, I will answer. If you are a troll PLEASE don't post. There's enough meanness in the world, don't add to it.